Your question: Can you use OSB on roof?

Both OSB and plywood panels can cut and installed on a roof using conventional roofing equipment. They have similar structural characteristics, and can be used interchangeably. … OSB is now the most-used sheathing and subflooring material for new roofs and roof replacements.

What type of OSB is used for roofing?

Typical types of wood used for roof sheathing are oriented strand board, known as OSB, and plywood, the most popular being OSB. Sheets of 7/16-inch thick, with no edge support, can be used in an area where the snow load is 30 pounds per square foot. With edge support and the same snow load, 3/8-inch OSB can be used.

What thickness OSB should you use for a roof?

Standard roof sheathing thickness is ½” to ⅝” thick. If you are using OSB for your roof deck, then ⅝” is the recommended thickness. For plywood, which is slightly stronger than strand board, ½” thick is appropriate.

Is OSB OK in the rain?

Your framing lumber and the oriented strand board (OSB) are going to be fine. The glues used to make OSB are water-resistant because the manufacturers know that virtually no one can build a home that won’t get wet before the roof and siding is applied. … The OSB floors should be swept clean each day after work concludes.

INTERESTING:  Is corrugated roofing noisy?

What is better for roof OSB or plywood?

Plywood Holds the Moisture Advantage Over OSB

When plywood gets wet, it tends to swell. … OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.

Which wood is best for roofing?

Cedar has earned a reputation for being strong, flexible, and weather resistant – qualities that make for an effective roofing shingle. Among roofing shingle manufacturers, cedar is the go-to material, all thanks to its durability.

Can you use 7/16 OSB on a roof?

Standard types of wood designed for roof sheathing are oriented strand board, known as OSB, and plywood, the most popular being OSB. Sheets of 7/16-inch thick, without edge support, can be used in an area where the snow load is 30 pounds per square foot.

Is OSB OK for shed roof?

For an inexpensive, value option 9mm OSB can be used for your garden shed roof. Start by fitting the beam across the top of the shed, slotting it into the pre-cut grooves at the top of the two pointed ends on an apex shed (known as the gable ends).

What can I use for roof sheathing?

Oriented Strand Board (OSB) or plywood can be used, although plywood will provide higher nail head pull-through resistance. Use panels rated as “Exposure 1” or better. Install sheathing panels according to the recommendations of the Engineered Wood Association (APA). Use panels no smaller than 4 feet long.

INTERESTING:  How do green roofs reduce energy?

Which side of OSB goes up on roof?

OSB roof panels should always be installed with the grade stamp facing into the attic and the screened surface (with the nail guide lines) facing up.

Which plywood is best for roofing?

Exterior Plywood is the preferred material for roofing. It also performs well when exposed to moisture over long periods of time. The price is low compared to other roofing materials and the installations are also easy.

How long will OSB last outside?

How Long Will OSB Last Outside? Oriented strand board will commonly withstand 3 to 6 weeks of exposure on a construction site without issue. EXPOSURE 1 panels have a waterproof bond and often experience unprotected exposure for six months on building sites.

What do you seal OSB board with?

Sealing OSB. For cases where OSB is more likely to be exposed to moisture, it’s a good idea to coat the OSB on the surface and edges with a waterproofing product, such as Thompson Water Seal, Flex Seal, or Liquid Rubber’s waterproofing sealant. Even latex paint will work.

How long can you leave OSB exposed to weather?

OSB 3 is classified as resistant to humid conditions. This is a liability choice to avoid misunderstandings. We have had OSB 3, also in horizontal orientation, exposed to rain for at least 4 months. Even puddles were forming and deliberately ignored by us.