What do you call where the roof meets the wall?

The sloped edge of a roof over a wall is the rake. The squared-off end of a sloped roof is called the “rake.” The ridge is the horizontal peak of the roof. Elk Roofing. The ridge is the peak where two sloped roof sections meet.

What is it called where a roof meets a wall?

A headwall is a level junction where a roof meets a wall.

What is it called where roof meets siding?

Drip Edge

It attaches right at the point where the edge of your roof meets the siding of your home.

What is the roof border called?

Eave: An eave is the lower border of the roof that overhangs the wall usually located in the first three feet of a roof. Undereave vent: Undereave vents are intake vents located under the eaves of the roof that help draw cool dry air into the attic.

What are parts of a house roof called?

These are the parts of a house’s roof:

  • Roof plane: This is the surface of the roof. …
  • Ridge: This is the top or peak of the roof, where two roof planes meet.
  • Valley: This is where two pitched roof faces connect and project inward. …
  • Dormer: This is a roof feature that projects out from the roof face.
INTERESTING:  Can you thatch a roof in the rain?

What is a roof valley?

A roof valley is formed where two roof slopes meet. Water collects in a valley to flow off the roof. Your choice of valley installation method is critical because, when improperly installed, valleys are risks for serious leaks. Essentially, there are three main ways to shingle a roof valley: woven, closed-cut and open.

What is soffit and fascia?

The soffit is part of the overhang where your roof meets your siding. … The fascia is the attractive board along the side of the overhang and the roof that helps your roof appear finished. Your gutter sits atop the facia board. The fascia is also known as a “transition trim” between the home and the roofline.

What is sub roofing?

A sub-roofing system can be the solution. … They consist of metal roofing suspended beneath upper deck areas to direct any moisture and liquids to a gutter that drains to a storm system.

What is a roof facet?

A facet is one section (plane or surface) of a multi-sectioned roof that is over 4 square feet.

What is a roof fascia?

What is Roofing Fascia? Roofing fascia forms the vertical finishing edge that connects your roofing to rafters, trusses, or gutter attachments. You see it beneath the roof’s overhang. Fascia is typically made of a wooden board or non-corrosive sheet metal.

What is a roof apex?

An apex roof has two slopes, which both meet in the middle – the highest point of the roof. … The front of the timber building is most commonly the side with the highest point of the pent roof and it then descends to the back.

INTERESTING:  How do you change the pitch of a roof in chief architect?

Where do two roofs meet?

The ridge is the peak where two sloped roof sections meet. Part of a roof’s frame, a ridge board runs horizontally along the peak of a sloped roof.

What are the 6 roof parts?

No matter what roofing material you choose – wood, asphalt, or tile roofing, these elements are important. They may have slightly different names but all are necessary.

Six Components That Make Your Roof Work

  • Starter Shingles. …
  • Flashing. …
  • Underlayment. …
  • Roofing Material. …
  • Ventilation. …
  • Hip and Ridge Shingles or Caps.

What is the structural part of a roof?

First is the frame of the roof structure. The truss is the “skeleton” of a roof, made of a series of parallel beams. The rafters are the supporting beams that run from the apex to the bottom of a roof, holding up the truss. Eaves are the edges of a roof, typically overhanging the vertical exterior walls of a building.

What holds the roof of a house?

Trusses are pre-fabricated, triangulated wooden structures used to support the roof. The alternative is to build up the roof’s frame with 2x8s and 2x10s. Trusses are quite common these days because they have five big advantages from the builder’s standpoint: Trusses are incredibly strong.